How to specify carpet tiles
The specification decisions that determine whether a floor still looks acceptable in year twelve — and the ones that only determine how it looks on day one.
On this page
Wear classification
European standard EN 1307 classifies textile floorcoverings by use class. The two figures you will see on British commercial carpet tile are:
| Class 32 | General commercial use |
|---|---|
| Class 33 | Heavy commercial use — the standard expectation for UK contract specification |
| Heavy Contract | Manufacturer designation used on fibre bonded ranges, indicating suitability for the most demanding commercial duty |
Almost every Burmatex range is rated Class 33 heavy commercial or Heavy Contract. Treat Class 33 as the floor, not the ceiling — it tells you the tile is fit for commercial duty, not how it will look in year ten. The figures below tell you that.
The numbers that actually predict performance
Pile weight (g/m²)
The mass of face fibre per square metre. More fibre in the wear layer, all else equal, means more to wear away before the backing shows. Across the Burmatex range this runs from 470 g/m² (Go-To) to 1490 g/m² (Chevrolay and Grimebuster). It is the single most useful comparison figure — but only within the same construction. Comparing a 600 g/m² tufted loop with a 1200 g/m² fibre bonded tile tells you almost nothing, because the fibre is doing a different job in each.
Castor chair rating
“Continuous use” is what you want in any office with wheeled chairs, and it is what every Burmatex range carries. Anything less than continuous use in an open-plan office is a specification error you will be looking at within three years.
Total thickness (mm)
Matters for two reasons that have nothing to do with durability: junctions with other floor finishes, and door undercuts. If you are working over an existing access floor or matching into resilient flooring, the thickness difference is a detail someone has to draw. Burmatex ranges run 5.5 mm to 12 mm.
Total recycled content (%)
Increasingly a tender requirement rather than a nice-to-have. Burmatex publishes figures from 48.8% to 77.9%. Full range-by-range table.
Impact sound reduction (dB)
Relevant in multi-storey buildings, student accommodation and anywhere Part E of the Building Regulations is in play. Fibre bonded Burmatex ranges publish around 21 dB.
Tile or plank?
Square tiles are 50cm x 50cm. Planks are 25cm x 100cm. Burmatex offers Arctic, Tivoli and Tivoli Mist in both formats at identical build height, so the two can be mixed without a transition detail.
Choose planks when you want linear direction, herringbone or ashlar layouts, or wayfinding expressed through geometry rather than colour. Choose tiles when you want the lowest wastage, the fastest installation and the most forgiving replacement.
Wastage: budget 5–7% for square tiles on a rectangular floor, 10–12% for plank and herringbone layouts, more for heavily cut floors.
Adhesive and subfloor
Most carpet tile failures are subfloor failures. Before specifying an adhesive system:
- Test subfloor relative humidity. A new concrete slab takes roughly one day per millimetre of thickness for the first 50 mm to dry under good conditions — longer below that. If it is not dry, a damp proof membrane is not optional.
- Specify a smoothing compound. Carpet tile telegraphs ridges, trowel marks and old adhesive residue far more than people expect.
- Tackifier vs permanent adhesive. A tackifier holds tiles in place while allowing clean lift for replacement, rotation and end-of-life recycling — the default for most commercial installations. Permanent adhesive is specified on ramps, in heavy trolley environments and where lateral shear is severe.
- Underfloor heating and high-temperature climates change adhesive selection. Check the manufacturer's guidance for the specific range.
Specification checklist
A clause that covers these points will not get argued with on site:
- Manufacturer, range name and colourway reference
- Format and module size (50 x 50 cm tile / 25 x 100 cm plank)
- Construction (fibre bonded / Structure Bonded® / loop pile / cut pile) and gauge
- Yarn composition
- Pile weight in g/m² and total thickness in mm
- Wear classification and castor chair rating
- Total recycled content %, and EPD reference
- Fire classification to BS EN 13501-1
- Laying pattern (monolithic / quarter-turn / brick bond / ashlar / herringbone)
- Adhesive or tackifier system, named
- Subfloor preparation requirement and moisture test standard
- Wastage allowance %
- Attic stock quantity — one to two boxes per colourway from the original batch
- Warranty period (Burmatex ranges carry 10 or 15 year wear warranties)
Frequently asked questions
What does Class 33 mean on a carpet tile?
Class 33 under EN 1307 designates heavy commercial use. It is the standard expectation for UK contract specification and is carried by almost every Burmatex range.
What pile weight do I need for an office?
For an open-plan office with continuous castor chair use, a dense tufted loop from around 600 g/m² upwards performs well, and a fibre bonded tile from around 950 g/m² will outlast it in the traffic lanes. Compare pile weight only within the same construction type — across constructions the figure is not comparable.
How much attic stock should I order?
One to two boxes per colourway, from the original production batch, stored flat and dry on site. Dye lots and production batches shift over years; matched replacement stock is what makes modular flooring"s replacement argument real.
Should I use tackifier or permanent adhesive?
Tackifier for most commercial installations — tiles lift cleanly for replacement, rotation and recycling. Permanent adhesive on ramps, under heavy trolley traffic, and anywhere lateral shear is severe.
What laying pattern should I specify?
Quarter-turn is the safest default: it hides shading, tolerates individual tile replacement and is forgiving of everything. Monolithic gives the most seamless appearance but is least forgiving. Brick bond, ashlar and herringbone suit planks and directional schemes.
Designed and made in Yorkshire
Burmatex has manufactured at Victoria Mills in Ossett, West Yorkshire since 1967, on a site the business has occupied since 1912. Design and production sit side by side under one roof — and every range on this site is available for export.